Mounts & Brackets

The Catrike Mirror/Computer Accessory Mount attaches to the lower handle bar to easily allow you to mount a mirror and/or a bike computer display. Works with computers that have a rotational mounts. Mirror and computer not included. Choose from a right or left configuration based on when you sit on the trike.

Provides a perfect attachment point for a computer, GPS, cell phone mount, bell, etc. This design allows infinite position adjustment on Greenspeed's mirror/fender mount post (not included).  This unit mounts on the Mirror/Fender mounts for the GT20 or 26 or the GT Series II & Magnum trikes.

Product Notes:

• Machined aluminum.
• Length: 2.5"
• Accessory Mount only. 
• Note: Mounting Post and Grab Handles sold separately.

This ICE designed strong and ridgid front light mount is bolted to the mounting points on the front derailleur post. Both handle bar type lights and dynamo lights can be fitted together on the mount.

Works on front booms with twin M5 bosses only - 2008 onwards.

Universal Computer, Light and Accessory mount made specifically for recumbent bikes and trikes. The Ucam base plate can be mounted onto any round tube frame from 1" in diameter to 2.5" in diameter. Mounts easily onto square tube frames as well. Also, this has hole locations to be bolted to water bottle mounts if desired. The mounting holes are 6.4 cm center to center. The mounting bar is 4.1 cm long and the diameter is 2.2 cm.

This mount works when you are using bar end shifters on your trike or want a second mirror. Works with the Mirrycle Mountain Mirror. Also works to mount other accessories like computers, bells, etc. Overall Length 4". Extends mirror 2 7/8" from bar.

Ever wanted to attach a computer, GPS, motor controller, or phone right near your hands? Ever wanted to attach something like a mirror to the ends your handlebars, but you have Bar End Shifters, so there wasn't any way to do it? Well, now there is!

This mount uses a special clamp with a Cable Tunnel in it that attaches to the end of your handlebars right under your Bar End Shifters. The clamp goes forward and inward a little bit and holds mounting tube that goes up and then out. Since the clamp goes inward a little bit, your hands slide right past it. You'll barely notice it's there as you go from braking to shifting and back. What you will notice is that your mirror is now right where you want it to be, and that you can easily see your phone and operate the buttons on your motor controller.

Since your hands need to move up and down from the brakes to the shifters and back, the clamp is angled and specially shaped to stay out of the way. It's curved and doesn't have any sharp corners, so as your fingers brush past it, you'll hardly notice it's there. The L shaped tubular mount goes up and out, putting an adjustable height horizontal tube about 2 inches (50mm) above and in front of the shifters. It works on both the left and right sides by simply flipping the components around.

Specs:

Machined from 6061T6 aluminum, anodized black. Fasteners are stainless steel. Clamp attaches the end of your 7/8 handlebar and has a tunnel that goes around the shifter cable. The L shaped Accessory Mounting tube provided is black powder coated 7/8 diameter 6061T4 tube.
Works with cable in front (Most Catrike, HP Velotechnik, Azub, Etc.)

The ICE Side Bag Mount can be fitted to either side of the seat, or just install two to have one on each side. The design has been improved with a black-anodised finish and laser-etched ICE logo. It is built to fit a standard bicycle handlebar bag and is very useful for accessing items without getting off the trike. The mount clamps to the 1" diameter cross bar on the back fo the seat and has a maximum recommended load of 8 lbs (3.6 Kg).

Reaching your water bottle becomes even easier by repositioning your bottle cage higher, angled up and inline with the upper body.

• Mount for holding bottle cage
• Holds bottle at an angle for easier reach

For all HPV Trikes: Attaches to the bottom of a tie rod and provides a place to mount your computer sensor.

Easy way to add an extra mounting point for a bottle cage onto the rail on the back of the mesh seat frame.

Attaches to your Greenspeed's front derailleur mast mounting tab to provide an ideal mounting point for most lights. Quality machined aluminum.

• Does not work on Anura.

This mounting bracket allows you to mount a taillight in different positions on your recumbent (chain stay, seat stay, seat frame, etc.)

• Some shimming may be required depending on the application.
• Medium: Fits 15.8mm or 2/3 inch tubes.
• Upper Volae seat stay measures 12.7mm, lower seat stay measures 16.5mm and chainstay (mid measurement) 27.1mm.

This barend with slotted clamp is 120mm long. It is used to attach accessories like a computer, phone mount, GPS, electric assist console, etc. to HP Velotechnik handlebars.

Ever wish you could mount a mirror off to the side of your handlebar? Ever wish you could put your computer right at the top of your handlebar? Ever wish you had a hand rest on the end of your handlebar? Ever wish you had something to grip to give you a little extra boost to get on and off the seat? Well, sometimes wishes come true! This mini T-bar plugs in and clamps on to the end of your handlebar and lets you do all those things and more! See Specifications for more details.

• Fits into any handlebar that can take bar end shifters (bars with 3/4 inch inside diameter, most bars are made this way). Double sided clamp grips the outside end of your handlebar and the vertical part of the T.
• Diameter of the horizontal portion is 7/8 inch (22.2mm), the same as a standard handlebar, so all kinds of things can be attached. We do not recommend that you attach controls like shifters and brakes, however.
• 4 inches (100mm) wide and 3 inches (75mm) tall. Requires 1.5 inch (38mm) of insertion into the handlebar for a net height above the end of the handlebar of 1.5 inches (38mm). Requires 3/8 inch (10mm) of clear handlebar end to clamp onto. Made from black powder coated aluminum.
• Any bike or trike with 7/8 inch outside diameter and 3/4 inch inside diameter handlebars (almost all under seat handlebars are made this way).

Cockpit mounts are a new way to hold things like cycle computers, mirrors, GPS units, cameras and phones close at hand, right where you want them. Unique articulated mounting system lets you work around obsticales and put things right where you want them. Quick attach open ended mounts- no need to slide on past anything, so there's no need to remove anything first when mounting the cockpit mount. See Specifications for more details.

• This Cockpit Mount Kit is designed to attach to a 7/8in Vertical Tube (22.2mm) tube (the diameter of your handlebars where the controls attach). The mounting clamp is 1/2in (12.7mm) thick, so all that's required is 1/2in of reasonably straight tube to clamp to. Because of the strength of the clamps, we don't recommend clamping to Carbon Fiber tubes. Other than that, if you have 1/2in of clear space on a 7/8in tube that's either straight or not curving very much, you can attach this mount. In most underseat steering applications, you'll attach it just below where the brake lever clamps on.
• The double ended clamps hold the centers of the tubes 2in (50.8mm) apart. With the two clamps in this kit joined by a central pivot tube, the T Bar where your accessories will go can be anywhere in the range about 0 to almost 4 inches (101.6mm) away from the tube you clamp to. The T Bar is 5in (125mm) wide and 9 in (225mm) tall. It's asymetric so you can point it inboard or outboard. The link/pivot tube is 1.5in (40mm) tall. You are free to mix and match and rearrange the clamps, pivot tube, and T Bar to get the perfect location for your accessories.
• By putting the right amount of tension on the clamps, you'll find it's very easy to move things around and find the ideal position for everything. Once you've determined your ideal position, just tighten the clamps to lock everything in place.
• The T Bar is 7/8in diameter, so anything that's made to attach to a handlebar will be happy there. To attach a mirror inside the T Bar, simply remove one end cap and install the mirror as if it were on the end of a regular handlebar.
• Note that while Cockpit Mounts are plenty strong for holding accessories, they are not strong enough to serve as an exit assist.
• Weight: 180 grams

Universal Handlebar Light Bracket DETAILS

• Fits Bars Up To 31.8mm Horizontal & Vertical Adjustable
• Easily Removes From Bar In Seconds
• No Tools Needed
• Compatible: TSL-100, TSL-150, TSL-150+, TSL-200, TSL-250, TSL-250+, TSL-500, TSL-500+, TSL-1500, SL-155, SL-255, USL-155, USL-305, USL-505, TSL-350, TSL-550, TSL-750, TSL-T1000, TSL-LT1000, TSL-1200, TSL-1800, TSL-2500, HL-1.1, & SL-30WP
• NOT Compatible: SL-200, SL40WP, TSL-500M, TSL-500R/RW, TSL-750M, TSL-750R/RW, TSL-1000M, TSL-1000R/RW

This innovative accessory mount is ideal for mounting headlights or computers to the derailleur mast or handlebar of your recumbent. It can also be used to solve a large variety of other accessorizing problems. Minoura Handlebar Accessory Mounts use the Quick clamp system that allows users to install and remove accessories with ease. See Specifications for more details.

• Holds up to 2 accessories (light, computer, bottle cage holder, etc.)
• Lightweight and rustproof alloy construction.
• New LW-Clamp reduces weight - 25 grams comparing to previous model.
• Alloy bar is position adjustable.
• Hex wrench required for installation/removal.
• SGS-400-STD: Standard size clamp (22.2 to 28.6mm diameter)

Incredibly versatile, the Adjustable Water Bottle Mount can hold up to two different water bottle holders in a variety of heights and angles. Either fine tune your angle for perfect reaching capability, or lock in to one of three preset positions for ease and maximum staying power; then bolt your water bottle holders at a height that works best for you! Bolts in place on any standard bottle mount location. Great for trikes, your bottles can be more vertical so no drips, the Adjustable Water Bottle Holder will make sure your bottle is never out of reach again!

The angle of the mast can be adjusted from straight up (perpendicular) down to 45 degrees. The mount can be attached facing backwards or forwards, so the effective range is 45 degrees forward to 45 degrees backward. There are 3 pairs of holes for mounting bottle cages on the mast. Two pairs are down low (where you usually want your bottles to be) and one pair is higher. The higher pair is used to mount the second bottle cage on the acute (inside) angle side when the mast is angled all the way down to 45 degrees.

• Mounts anyplace you can put a regular bottle cage. Holds 2 standard water bottle cages anywhere from 45 degrees to 90 degrees from the surface it's mounted on. Can be angled forward and back by reversing how it's attached.
• Made to hold 2 standard water bottle cages and designed to carry 2 water bottles worth of weight.
• Base is slotted to fit any bottle bosses in the standard bicycle range. 5mm threaded holes on the mast are centered on the standard. 3 pairs of holes are provided on the mast so you have both cage height options and to make sure there is clearance so your bottle won't touch your frame if it's on a cage on the acute (inside) angle side even if the mast is adjusted all the way down.
• CNC machined aluminum, black anodized and laser marked. We provide 5mm stainless button head bolts for both the frame attachment and the bottle cage attachments. We think the button heads look better and work better because the heads are wider and flatter. Wider works better on slotted things like bottle cages, and the flatter heads give more clearance so your bottles won't hit the bolt heads.
• Fits any bike/trike with standard bottle cage mounting bosses. This mount is most suitable for bikes and trikes where the existing bottle cage mount is basically horizontal, and you would prefer that it be more vertical. Can theoretically be attached to an add on (clamp on) mount, but the mount would need to be very strong if you want to run 2 bottles.

Shown with optional Water Bottle Cages.

Gain more room or find the perfect position for lights, computers, MP3, GPS, or whatever with the BarXtender. The base of the BarXtender rotates to allow for multiple adjustments. There is also the option to pivot the mount to find the ideal angle. Mount to the front derailleur mast on your recumbent for the perfect position!

• Clamp: Fits 22 to 38 mm (shims included)
• Crossbar: 25.4 mm
• Material: Engineering Grade Plastic and Steel
• Mount: Handlebar, Derailleur mast
• Size (L x W x H):18 x 3 x 3 cm or 7.1" x 1.2" x 1.2" (folded) and 13 x 10 x 3 cm or 5.1" x 3.9" x 1.2" (open)
• Weight: 116 g / 4.08 oz

Side Bag Mounts for Scorpion with ErgoMesh seat:  Need some easy to reach storage? Our pair of Side Bag Mounts is fully adjustable with a max. payload of 11 lbs. per side. Compatible with many clamp-on accessories. Includes mounts for left and right sides, with mounting hardware and instructions.  Retrofittable and ready to ship.

One of the great things about triking is how nice it is to have everything right at hand as you roll along. With a SeatSide mount, you can have all sorts of things close at hand.

The Catrike SeatSide Mount lets you carry bags, water bottles, cameras, all sorts of things, right by your side. Snacks, phones, lip balm, you name it, now you can keep it all within reach while riding.

This version of the SeatSide Mount for Catrikes attaches to the back of the folding seat frame. We make other versions that attach to the main frame tube. We recommend this version of the mount for people that simply want a good sturdy place to mount things beside the seat. If you want maximum versatility in where things are located or need quick on/off removability, check out the main frame mounted version.

Clamps are CNC machined aluminum, anodized black, with all stainless fasteners. Tubes are black powder coated aluminum with removable black end caps.

Note
This product only includes the mount itself. Bags, cages, and other accessories are sold separately.

A handy tool for mounting bike gadgets.

This accessory mount can be attached to the end of the Rover to provide a place to attach common bicycle accessories such as a headlight or bike computer.

Compatible with Rover model only.

This Mirror/Fender mount attaches to either front wheel kingpin and works perfectly with the Mirrycle Mirror. Many riders have a mirror mounted on each side of their trike (two mounts required). The Greenspeed Grab Handles can also be attached to the top end of this mount (two mounts required).  Or add a Greenspeed Accessory Mount to mount your computer.  This is also the mounting point for Greenspeed Fenders. 

Product Notes:

• Fits kingpins (non-threaded) on the GT20 & GT26 models. 
• Sold individually.  Note: Two mounts are required for fender installation, Grab Handle installation and for two mirrors.

Keep your water bottle within easy reach with Bontrager's Handlebar Bottle Cage Clamp, which mounts directly to the handlebars and allows you to add a bottle cage to the front of your bike within easy reach.

FEATURES

• Handlebar-mounted cages provide alternative placement for bikes without mounts
• Clamp only (no cage), fits both 22.2mm and 25.4mm bars

Topeak Versamount water bottle mount is a versatile mount for additional water bottle cage or other accessories. Band style clamp provides easy installation and flexible mounting options. Helps solve bottle fit issues due to frame designs.

Our new and improved computer bracket lets you mount any cycle computer safely and easily. The bracket is:

• More adjustable
• Fits wide range of computer sensors
• Sensors mount more securely

The TerraCycle Accessory Mount is a great multi-purpose mount for installting lights, computers, etc. on a variety of bikes (especially recumbents). Three arm sizes are available.

Clamps sold separately.

• Choose ONE ARM SET (select size) and ONE PAIR of CLAMPS (select size) to receive a complete mount that clamps to a tube.
• Or, choose ONE ARM SET (select size) and ONE PAIR of 90 Degree Accessory Mount Adapters
  to receive a complete mount that bolts to a bottle cage style braze-on.
• Can be mounted to derailleur masts, seat stays, handlebar masts and some fork blades
• The 1-1/8" fits derailleur masts on Volae, RANS, Greenspeed, and HP Velotechnik, Vision, Bacchetta.
• The 1-1/4" fits derailleur masts on Catrike, ICE, and TerraTrike.
• An optional Extender Kit is available and can be special ordered.
• Accessory Mount arm lengths are 50mm, 75mm, and 100mm.
• The mounting tube in the middle is 1 inch (25.4mm) in diameter. Nearly all bicycle accessories will work on a 1 inch tube.
• Accessory Mounts are machined from 6061-T6 aluminum, then black anodized.
• All bolts are stainless steel.
• The arms can be independently rotated 360 degrees and locked in any position.

The Universal Top View Mount is a great solution for your HP Velotechnik or other trike or bike with bar end shifters, to have your GPS, mobile phone, or any other small electronic device in your field of view (Top View).  It is compatible with under seat steering and Shimano and Microshift bar-end shifters.

This handy little bit replaces the nut on your quick release skewer so you can mount a headlight. Why? Maybe your handlebars are already too cluttered with your bell, smart phone, cyclometer, map clip, mirror and coffee cup holder. Or maybe you just like the way it looks.

• Lower mounting position provides a broader beam of light
• 22.2mm diameter, knurled clamp surface holds lights steady
• Not recommended for rear-wheel use
• Don't step on it

One of the great things about triking is how nice it is to have everything right at hand as you roll along. With a SeatSide mount, you can have all sorts of things close at hand.

The Terratrike SeatSide Mount lets you carry bags, water bottles, cameras, all sorts of things, right by your side. Snacks, phones, lip balm, you name it, now you can keep it all within reach while riding.

This version of the SeatSide Mount for Terratrikes attaches to the main tube of your trike for maximum versatility. We make other versions that attach to the seat frame. We recommend this version of the mount for people that have a 3.X, Tour, Tour II. etc. with the seat more than half way forward. On the 3.X and Tour, the handlebars come in right to the side of the seat when the seat is in the forward half of it's range, so we recommend the frame mount version for those trikes when the seat is forward

This mount can be used on any TerraTrike except for the Rover and the Edge. Since this mount attaches to the main frame, you have a lot of positioning options. This mount also includes the quick on/off option so the main arm can be quickly and easily removed and reinstalled for folding or transport.

Note
This product only includes the mount itself. Bags, cages, and other accessories are sold separately.

One of the great things about triking is how nice it is to have everything right at hand as you roll along. With a SeatSide mount, you can have all sorts of things close at hand. The Magnum SeatSide Mount lets you carry bags, water bottles, cameras, all sorts of things, right by your side. Snacks, phones, lip balm, you name it, now you can keep it all within reach while riding. This mount attaches to the horizontal brace on the back the seat. The mount comes out and forward to your side. The SeatSide arm can be attached on either side, or both if you wish.

Product Notes:

• This product only includes the mount itself. Bags, cages, and other accessories are sold separately.
• This single side mount works on the Magnum SD & Magnum XL.  If you want a double sided mount, those need to be special ordered and are different for the SD & XL.