Tools

Keep your Speed Drive, High Speed Drive or Mountain Drive in good working order.

This one is a no-brainer. The Park CC-3 Chain Wear Indicator could be the perfect tool. it’s so helpful, affordable and easy to use that it belongs in every roadie’s tool box — even if it’s the only thing in there because you’re so mechanically disinclined.

You won’t have any trouble mastering the CC-3. Just hook the curved end inside a link with the 0.75% scale on the bottom edge. Lower the tool to the chain. If the flange doesn’t drop in, keep smiling and go for a ride. The chain is practically as good as new.

The CC-3 is 5 inches (13 cm) long. It works on any bicycle chain, according to Park Tool. it’s made of laser-cut steel for precision and durability. It doesn’t seem likely to wear or be damaged by a lifetime of use.

Nice touch: When you flip to tool over to try the opposite scale, the lettering and number are still right-side up.

Many derailleur chains use a “master link” that allows the chain to be installed and removed by hand. While this type of master link doesn't require a traditional chain tool, over time, dirt and corrosion can make it difficult to separate by hand. MLP-1.2 Master Link Pliers make removal and replacement of these master links quick and effortless. Simply insert the specially sized jaws into the master link. Then squeeze the handles to open or pull the handles to close the link. Compatible with all 5, 6, 7, 8, 9, 10, 11 and 12-speed derailleur chains that use a master link.

The PW-5 is perfect for the home workshop or event tool box. Although economically priced, this 15mm pedal wrench, like all Park Tool products, is built to last. Made from heat-treated spring steel and vinyl dipped for comfort. 11 1/2” (29 cm) long.

The CN-10 Cable and Housing Cutter is a shop quality cutter designed specifically for use on all bicycle cables and housing, including hard-to-cut index housing.

Park Valve Tools. A small, handy tool designed to remove and install Schrader and Presta valve cores and to remove and install Presta valve extenders with 5mm wrench flats.

• Note: Not all Presta valve cores are removable

As far as multi-tools go there are a few things that every one should have and the Crank Brothers Multi-19 Tool has them all and more. The Crank Brothers Multi-19 tool will get you out of most mechanicals you might run into out on the trail. The multi tool is super light and comes with a lifetime warranty. Don't leave home without it.

• Allen Wrenches: 2,2.5,3,4,5,6 & 8mm.
• Stainless steel chain breaker.
• 2 Phillips and 1 Flathead screwdrivers.
• 4 spoke wrenches - #1/#2/#3/#4
• 8 & 10mm open wrenches.
• Torx t-25 & t-10 wrenches.
• 6061-t6 Aluminum frame.
• 175 grams w/o Tool Flask.
• Also includes a stainless steel carrying flask.

This small chain tool goes anywhere and actually performs like a shop quality tool. The fine thread, special “V”- shaped handle, and super strong replaceable pin make chain removal and installation a breeze.

A shop favorite updated to work on all chains including 1/8”, 3/16” single-speed chains and 5 to 11-speed 3/32" derailleur chains. Because of the tremendous force needed to remove chain pins, our Chain Tool is made from investment cast steel.

Park Spoke Wrenches are precisely sized for the spoke nipple and made from durable materials that provide years of dependable use.

• Precision sized to fit the three most popular spoke nipple sizes on the market, .127"/3.23mm, .130"/3.30mm and .136"/3.45mm
• Nickel plated for years of service. Designed for the home mechanic

A professional quality shop chain tool that works on 5-speed to 12-speed Road and Mountain Bike derailleur chains, including SRAM AXS 12 speed, as well as 1/8" and 3/16" chains. The CT-3.3 features an adjustable locating shelf so it works on any width chain to remove and install chain rivets. Built to last and easy to use, the CT-3.3 features a comfortable handle, investment cast steel body and replaceable driving pin

• The CT-3.3 will install, but not peen, Campagnolo 11 and 12-speed chain rivets
• Comfortable T-handle
• Replaceable driving pin
• Investment cast steel body
• Adjustable locating shelf

The 45NRTH stud insertion tool seats and removes the stud from the stud pocket. Customize your stud tread pattern or replace missing studs. Works with all 45NRTH studdable and studded products.

• Tire studs sold separately
• POM-injected handle
• Stainless steel barrel
• Thumb and index finger grips for more comfort and control
• Compatible with studs that have a 3.5mm or smaller shaft

This 17 function, super-light multi tool previously won the Editor's Choice Award for Best Multi Tool in Mountain Bike Magazine. It's very quickly winning our votes too! Lifetime warranty.

• Allen Wrenches: 2, 2.5, 3, 4, 5, 6 & 8mm.
• Stainless steel chain tool.
• Phillips and Flathead Screwdrivers.
• 4 spoke wrenches - #1/#2/#3/#4
• 8 & 10mm open wrenches.
• Torx T-25 wrench.
• Lightweight 6061-t6 aluminum frame.
• Only 168 grams.

Keep this 15mm crescent wrench in your bike bag so you can easily remove your BionX or Falco rear wheel and change a tire, or periodically check the axle nuts and tighten them up to 40 Nm (30 foot pounds).

Bottom bracket tools intended for both shop and consumer use.

The BBT-9 is used to remove and install external bearing crankset bottom brackets. One end of the BBT-9 securely engages the 16 notches of the bottom bracket cups. The other end of the tool engages the 8 internal splines of the crank arm adjustment cap.  The BBT-9 fits cups and lockrings with 16 external notches and an outside diameter of approximately 44mm.

The BBT-9 works with many external bearing crankset bottom brackets, including:

These pins fit Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. Made from hardened alloy tool steel.

Uses 7mm or 9/32" 12 pt box end/socket.

Folding 5-12 speed compatible chain tool even works with Campagnolo chains that requiring peening. Smooth and powerful, this handy take along is encased in a stainless steel shell, which becomes a comfortable handle when opened.

Crank Puller for Square tapered Cranksets.

This shop quality tool will easily remove cranks that require a 14mm socket or 8mm hex release.

Double ended cone wrenches designed for the home mechanic or occasional user. Thin enough to adjust narrow and hard to reach cones.

Made of thin steel and are nickel plated and heat treated for long use
Small tool size to carry along for quick repairs
Fits 13 and 15mm cones

Double ended cone wrenches designed for the home mechanic or occasional user. Thin enough to adjust narrow and hard to reach cones.

Double ended cone wrenches designed for the home mechanic or occasional user. Thin enough to adjust narrow and hard to reach cones.

• Made of thin steel and are nickel plated and heat treated for long use
• Small tool size to carry along for quick repairs
• Fits 17 and 18mm cones

Double ended cone wrenches designed for the home mechanic or occasional user. Thin enough to adjust narrow and hard to reach cones.

Park Tool Freewheel Removers are made from durable, heat treated alloy tool steel for long life.

Hex wrenches made from industrial tool steel, hardened and tempered for shop use.   Available in Y-Shape for convenience and quick adjustment, L-shape for hard to reach areas and where additional torque is required or Folding version when multi sizes are needed in a small package.

Includes 4,5,6mm hex keys, flat blade screwdriver and T-25 Torx driver

The Park Tool Fold Up Hex Wrench Set combines all the popular hex wrench sizes into one convenient fold-up tool, eliminating the need for a mess of loose tools. Its multi-position composite handle is comfortable, lightweight, slip-resistant, and 40% stronger than steel handles.

The Park Tool Fold Up Hex Wrench Set combines all the popular hex wrench sizes into one convenient fold-up tool, eliminating the need for a mess of loose tools. Its multi-position composite handle is comfortable, lightweight, slip-resistant, and 40% stronger than steel handles.

Park Tool Hex wrenches made from industrial tool steel, hardened and tempered for shop use. Available in Y, L-Shape and folding versions

• Molded for hand comfort, AWS-1 is one of the most usedPark Tool Hex Key for everyday use
• Made from high-torque industrial steel with chamfered tips for tight tolerances
• Includes 4, 5 and 6mm Hex Keys

Hex wrenches made from industrial tool steel, hardened and tempered for shop use.   Available in Y-Shape for convenience and quick adjustment, L-shape for hard to reach areas and where additional torque is required or Folding version when multi sizes are needed in a small package.

Perfect for taking on rides, the strong, compact, lightweight IB-1 features our unique I-Beam handle surrounded by 3, 4, 5, 6 and 8mm hex wrenches and a straight blade screwdriver. Made in the USA.

A complete take-along tool combining our award winning I-Beam technology with a full array of emergency tools:

Compact and lightweight, features commonly used tools in unique I-Beam design.