Clearance

This ingenious kickstand mounting bracket allows a Greenfield Traditional Kickstand to be installed at the rear dropout. Works with all Volae, RANS Stratus, Stratus LE, and Vision 20/26 models.

Includes hardware and instructions.

• Not recommended for tandems.
• Click for Installation Instructions.
• Kickstands are not designed to hold the weight of the rider. Do not sit on the bike when the kickstand is in the down position, it could cause the kickstand to fail.
• See the Kickstand Fit List in our Help Guides section for more fit information.

Replacement mesh seat pad adds new cush to your Volae or Vision mesh seat. Fits both Original Volae Mesh Fabric seat (pre-2012 Volae and Vision), and the Comfort Volae Mesh Fabric seats.

Product Notes:

• Pad Dimensions:  16" wide x 10.75" nose to back x 2" thick
• Color of pad may be white, yellow or green.

These mounting brackets allow you to mount reflectors, taillights and other accessories in different positions on your recumbent (chain stay, seat stay, seat frame, derailleur mast, etc.).  The larger sizes work great for mounting cadence sensors on front derailleur masts for Garmins and computers.

Product Notes:

• Some shimming may be required depending on the application.
• X-Small: Fits 12.7mm or 1/2 inch diameter tubes.
• Small: Fits 15.8mm or 2/3 inch diameter tubes.
• Medium: Fits 19mm or 3/4 inch diameter tubes.
• Large: Fits 25.4mm to 26.8mm or 1 to 1 1/16 inch diameter tubes.
• X-Large: Fits 28.6 to 31.8mm or 1 1/8 to 1 1/4 inch diameter tubes.

Replacement seat bracket for all Volae hardshell seats. Black. Select Upper or Lower.

Product Notes:

• Lower bracket base: 3.25" wide x 3"
• Lower bracket mounting holes:  2" center to center
• Lower bracket skewer width: 2 14/16" outside to outside
• Upper bracket base: 3 7/8" wide x 2 3/4"
• Upper bracket mounting holes: 2.5" center to center
• Upper bracket skewer width:  5 3/8" outside to outside

These lightweight, cold forged Kalloy stems are available in a variety of sizes from 80mm to 140mm to fine tune the cockpit fit of your Volae. Attach to 1 1/8” outside diameter steering mast and have a 1” handlebar clamp. Color: Black.

If you're tired of arm discomfort, or simply looking for your perfect riding style, our Volae handlebars could do just the trick. Choose from two widths: standard or wide (new style one-piece bent bar).

Product Notes:

• Black anodized 6061 aluminum.
• Integrated 1" (25.4mm) stem clamp area.
• Grip sections of the bar are long enough (6.75") to easily accommodate both a GripShift and a V-Brake lever.
• The "Trimmed" bars have been trimmed for Volae recumbents.
  

Standard Specifications

• Width of bar at clamping area is 13 1/2"
• Width of bar at bend is 18 1/3"
• Width of bar at bottom of grips is 21 1/2"

Wide Specifications

• Width of bar at clamping area is 19"
• Width of bar at bend is 23"
• Width of bar at bottom of grips is 26 3/4"

Prevents "dang my chain came off" when down shifting to the Granny ring. Install the Granny Guard and loosen the front derailleur inner stop screw until it permits shifting under pressure. Now, go ahead --- shift right in the middle of that climb. You won't over shift. Gone are the days of struggling up a hill in the middle ring because you underestimated how steep it was and are afraid to downshift in the middle of the climb. View our video on YouTube for more info.

• Works on most recumbents.
• Works with 24t to 32t 74mm Bolt Circle Diameter (BCD) chainrings with a 5 bolt pattern.
• Center to center measurement of adjacent holes on a 74mm chainring is 43.5mm
• Includes 16mm chainring bolts and 3.5mm chainring spacers, which work with many stock granny chainrings.
• Vuelta and Salsa brand 74mm BCD chainrings require the 2.2mm Volae Chainring Spacers to properly attach.
• Will not work on most upright bikes due to contact of the Granny Guard with right chainstay.

Volae 17t rear idler with sealed 8mm bearing.

Replacement seat skewer for attaching the lower seat bracket to the seat slider on a Volae bike. This skewer is 95mm long with 25mm of thread. The skewer does not include the specialty nut. The Lower Seat Skewer Attachment Plate (specialty nut) is no longer available, as Volae is out of business. This skewer will also fit some Vision applications. See Product Notes for fit application. Skewer measurements are listed as being longer than the previous Vision measurements, because we are measuring the entire length of the skewer rod.

Product Notes:

• 95mm: Fits the Volae lower seat attachment assembly and captain seats on all Vision tandems.

Tandem length brake cable in stainless teflon.

• 1.6 mm x 2750 mm
• Corrosion Resistant
• Pre-Stretched
• Compatible with Road and Mountain Levers

Worried about dings and scratches? We've found a solution! Keep your Volae, or any other recumbent, looking like new with these handy frame paint protectors. The kit includes a Removable Vinyl Skid Plate for protecting the top of your frame from cleat scratches when you step over, a Permanent Chainstay protector, and a Permanent Headtube Protector to prevent cable rub.

Transparent when installed on frame. (frame protector highlighted for viewing purposes)

Replacement delrin frame plugs for Volae frames. These plugs allow you to attach the seat slider and quick adjust kit to the frame. Two pack. Black.

Will also work on Vision frames.

Get a seat that is comfortable, tough, light and aerodynamic. The Volae Comfort Carbon seat shells, with edging, have a wider seat base with more support and cup to it, providing a more supportive riding postion. Volae Comfort Carbon fiber hardshell seats are available in four sizes to fit your torso and weigh 2 lbs. 5 oz. (based on the medium seat without hardware or pad). See Specifications tab for sizing information.

Does not include pad, mounting brackets or mounting hardware.

Specifications:

Volae Seats are sized by Seated Shoulder Height.

• Small: 23" or less
• X-Large: 26.5" or more

Volae Comfort Carbon seats require longer mounting bolts than the original style Volae carbon seats. View the Comfort Carbon Hardware Kit.

Volae Front idler hardware assembly includes the chain keeper, nut, bolt and washers. Also works on Vision recumbents. Only works with the original Volae Front Idler.

If you are buying a new Volae Front Idler made by T-Cycle, then you will also require the Volae Front Idler Conversion Kit.

Replacement foam roll for Volae Headrests. 5.5" long by 4.25" diameter.

The same comfy seat foam from Volae is now available with a breathable cover that gives your seat a more finished look. The new cover can also be removed for washing and it protects your Lycra shorts from snags on the open cell foam. The replacement cushion has a 1/2” layer of closed cell foam bonded to a 1 3/4” layer of open-cell foam. Available to fit the new Comfort Carbon Seats. Order the cushion that matches your seat size.

Product Notes:

• The Volae cushions are designed to fit the Volae Comfort Carbon Seats.
• All pads are appx. 8.75" wide at the shoulders, 10.75" wide at the widest point (hips), and 2.5" thick.
• Length of the XS is 31".
• Length of the S is 32".

• Uses road brakes only
• 1" x 25cm threadless riser
• 33.5cm axle to crown
• Carbon fork blades with 7005 aluminum riser
• 40mm Offset

Riser for all Volaes with cable guides. 

Product Notes:

• 1" inside diameter (see below)
• Compatible with 1 1/8" stem clamps.
• Length is 14.5"
• Note:  This riser has a very tight fit and in order to get over the fork steer tube, it needs to be reamed to a depth of 4 inches with a 1.0060" specification.  It has a slight excess of material inside.

Optional chainring spacer kit works in conjunction with the Volae Granny Guard for Vuelta and Salsa small 74mm BCD chainrings. Set of five spacers.

• Use one spacer kit for Vuelta 74mm BCD chainrings.
• Use two spacer kits for Salsa 74mm BCD chainrings.

Replacement upper quick release skewer for attaching the upper portion of the seat bracket to the adjustable rear seat stays on all Volae bikes and tandems. Includes a standard skewer nut. 186mm

Will also fit some Vision applications. Skewer measurement is listed as being longer than the previous Vision measurement, because we are measuring the entire length of the skewer rod.

The Volae front brake cable adapter allows you to route your brake cable to the correct side of the frame with caliper style brakes.

Dual Pivot design with 39-49mm reach. Cartridge Style Pads.

Complete hardware kit to attach the upper and lower seat brackets to a Volae Comfort Carbon hardshell seat. Click on larger image to view order of installation.

Comfort Carbon Kit includes the following parts:

• Eight M6x25 bolts
• Sixteen rubber washers
• Eight large flat washers
• Eight small flat washers
• Eight Nyloc nuts

Dual Pivot design with 39-49mm reach. Cartridge Style Pads.

The Zefal Spin mirror works great on the ICE VTX or Sprint X series in conjunction with the ICE mirror mount if you want a more compact mirror.

Volae handlebar riser clamp has an inner diameter of 28.6mm. Black.

Replacement reinforced seat fabric for the Volae Comfort mesh seat used on 2012 and newer Volae bikes and tandems. Made in the USA. Pad sold separately. Will not work on a Vision.

Replacement seat skewer bolts for attaching the Quick Adjust Seat Slider to the frame on all Volae bikes. The 79mm skewer does not include the Quick Adjust Skewer Plate. The Quick Adjust Skewer Plate is no longer available, as Volae is out of business. Will also fit some Vision applications. See Product Notes for other fit applications. Skewer measurements are listed as being longer than the previous Vision measurements, because we are measuring the entire length of the skewer rod.

Product Notes:

• 79mm: Also fits Vision VR-30 and '99 & newer Vision tandem stoker seats.

Used inside Volae risers to attach the Aheadset adjusting bolt to the star nut. This clever device allows perfect adjustment of the headset on a Volae. It comes with four 1 cm spacers, which allow the rider to adjust lower the handlebars if needed. Use a tubing cutter to shorten the riser and simply remove the required number of spacers.

Product Notes:
When using the Volae Handlebar setup and the Aheadset Extender, you need to have at least three inches of fork steertube protruding above the topf of the headset. If you have less than three inches, you will need to use a TerraCycle Glideflex instead.

For skiers wanting a boot that will last the test of time while providing great comfort and enough grip when walking. The Escape combines an anatomical touring fit and central zip lace cover.

Benefits:

• Comfort - A slightly wider fit with anatomical features offers foot hold and maximum comfort.
• Protection - The lace cover with central zip provides protection against snow and water.
• Robustness - Salomon’s renowned quality and durability come together to make this boot your long-term touring companion.
• 105 Touring Fit - Generous anatomical shape for maximum comfort and warmth.

Technologies:

• Works with Prolink Bindings (two rails)
• Classic
• Nordic Touring

Volae Comfort Carbon Hardshell Seat includes mounting hardware, upper and lower brackets and the Dual Density Comfort Pad with Cover.  Compatible with all Volae bikes.

Featuring waterproof, breathable DryVent™ 2L, the thigh-length Arctic Parka is insulated with 550-fill Goose Down and 150g Heatseeker™ Eco for a flattering fit and a great warmth-to-weight ratio.

Features:

• Stormflap with hook-and-loop closure covers the two-way, VISLON® center front zip
• Adjustable hood with removable faux-fur ruff
• Covered, secure-zip, welt hand pockets
• Waterproof, breathable, seam-sealed DryVent™ 2L shell
• 550-fill goose down throughout the body and 150g Heatseeker™ Eco in the side panels for a beautiful fit and great warmth-to-weight ratio
• Rib-knit cuffs
• Standard fit
• Secure-zip, internal media-compatible pocket
• Embroidered logo on left chest and back-right shoulder

Click Here for The North Face Sizing Chart.